Inquiry
Form loading...

Shielded Without Gaps: Electromagnetic Shielding Sealant from Songxi Tech for Server and Switch Chassis Covers

2026-10-20

Servers and network switches combine fast signals, dense electronics, and metal housings, so designers must build electromagnetic compatibility in from the start. The weakest point of a die-cast chassis is rarely the metal itself but the seam between housing and cover. Songxi Tech's electromagnetic shielding sealant closes this seam: a one-component conductive adhesive is dispensed as a bead, cures into a conductive gasket, and replaces foam or spring fingers. It tolerates up to 50% compression and fully cures within 30 minutes at 150 °C.

微信图片_20261020133433_1174_18_upscayl_1x_upscayl-standard-4x.png

A closed metal husing is not automatically a closed shield. Wherever cover and housing meet, microscopic gaps remain between the contact points. At high frequencies, such a gap behaves like a slot antenna: the longer it is, the more efficiently it radiates, and the more interference leaves or enters the device. Devices must pass radiated-emission tests before they can be sold, so a leaking seam is expensive to find late in development. A gasket solves the problem by providing low-resistance contact along the whole seam instead of at a few screws.

Conductive adhesive as a dispensed gasket for die-cast chassis covers

Conductive foam and metal spring fingers are separate parts. They must be cut to length, placed by hand and held in position, and they follow complex flange shapes only with difficulty. With a dispensed, form-in-place gasket, a nozzle applies the conductive adhesive directly to the cover, and the bead takes the exact contour of the flange, including corners and the areas around screw bosses.

For this application, the adhesive has to meet one basic condition: the bead must stay on conductive coatings, die castings, and metal plating from dispensing to final assembly. A bead that lifts off the flange leaves exactly the gap it was meant to close. Songxi Tech's conductive adhesive is formulated for these surfaces, and because a machine controls position and cross-section, every housing receives the same gasket.

Electromagnetic shielding sealant for varying gaps: up to 50% compression

Stability and flexibility have to be balanced in a shielding gasket. Die-cast parts and thin covers show tolerances and slight warpage, so the cured gasket must deform enough to follow them while the cover is screwed down. At the same time, it must not stay deformed. The electromagnetic shielding sealant from Songxi Tech can be used with a compression ratio of up to 50%, which gives designers a wide working range for tolerance compensation.

This is combined with a low compression set, the permanent deformation that remains after long compression. The cured material springs back and keeps its contact pressure, so shielding does not deteriorate over the life of the device, for example after the cover has been opened for service. A wide compression range and a low compression set together determine whether the seam stays tight in the field, not only on the day of assembly.

Process-reliable dispensing of a one-component electronic sealing adhesive

The processing method has a significant influence on the quality of the gasket. This electronic sealing adhesive is therefore designed as a one-component system for automated dispensing: there is no mixing ratio to control and no pot life to monitor, which supports reproducible production. After dispensing, the bead is fully cured at a medium temperature of 150 °C for 30 minutes. In a typical process, it is cured on the bare cover in a continuous oven before final assembly, so no heat reaches populated boards.

Two practical points are worth planning early. Conductive fillers are abrasive and wear nozzles and pumps, so dispensing equipment should be selected accordingly. And because dissimilar metals in contact can corrode in humid environments, the filler and the housing coating should be tested together on the real part.

Electromagnetic shielding sealant from design phase to series production

Bead height, bead width, and compression range depend on flange geometry, coating, and tolerance chain, and requirements differ from housing to housing. Songxi Tech supports customers on request from the design phase to series dispensing, including bead geometry, dispensing parameters, and curing process.

Key points at a glance

Dispensed gasket: a one-component conductive adhesive is applied as a bead on die-cast flanges and replaces foam or spring fingers, with a bead that follows the exact flange contour.

Mechanical requirements: the electromagnetic shielding sealant tolerates up to 50% compression, and its low compression set keeps contact between cover and housing over time.

Process: as a one-component electronic sealing adhesive, it is fully cured at 150 °C within 30 minutes, without mixing.